Fireduino

拥有双核Cortex-M3处理器,集成高质量音频Codec和WiFi模组,拥有良好的IOT扩展性能,完美兼容Arduino IDE和Arduino标准接口,并支持FireBlock图形化编程软件,是一款首选的编程启蒙教学平台,更是一款开源的创意原型平台。

Fireduino TFT 通用绘图显示

更新时间:2017-08-08 阅读:14682

Fireduino TFT

Fireduino TFT 采用与传统的Arduino TFT 同属一些列的LCD 驱动器,为ST7735S,与Fireduino 通过I8080 接口连接,比传统Arduino TFT 的SPI 方式 刷新速率快一个级别。

Fireduino TFT库

Fireduino TFT 库 基于ST7735S 驱动扩展 Adafruit GFX 而成的TFT库,Adafruit GFX负责绘制图形,ST7735S 负责驱动LCD 显示屏,它兼容 Adafruit GFX API,Fireduino 连接 TFT 后如下图:
LCD SCH.jpg

LCD paint.jpg

Fireduino TFT 通用绘图显示

本案例演示如何在Fireduino 的TFT配件上绘制通用图像,在读取A0 电位值后显示条形图柱在屏幕上,形成一个连续的图块。

硬件要求

1.Fireduino board
2.Fireduino TFT board
3.电位器


代码

开始之前

使用TFT 屏幕,首先得包含TFT库头文件。

#include <TFT.h>

定义你的TFT 屏幕,并创建一个实例对象

TFT TFTscreen = TFT();


setup()

1.初始化串口,以供信息打印输出。
2.初始化屏幕。
3.设置背景色。

void setup() {
  // initialize the serial port
  Serial.begin(9600);
  // initialize the display
  delay(1);
  TFTscreen.begin();
  delay(1);
  // clear the screen with a pretty color
  TFTscreen.background(250, 16, 200);
}


loop()

1.读取A0 电位器值,并转换映射为屏幕高度比例值。
2.画图柱在屏幕上。
3.如果图柱画满屏幕宽度,清除屏幕后继续。

void loop() {
  // read the sensor and map it to the screen height
  int sensor = analogRead(A0);
  int drawHeight = map(sensor, 0, 1023, 0, TFTscreen.height());
  // print out the height to the serial monitor
  Serial.println(drawHeight);
  // draw a line in a nice color
  TFTscreen.stroke(250, 180, 10);
  TFTscreen.line(xPos, TFTscreen.height() - drawHeight, xPos, TFTscreen.height());
  // if the graph has reached the screen edge
  // erase the screen and start again
  if (xPos >= 160) {
    xPos = 0;
    TFTscreen.background(250, 16, 200);
  } else {
    // increment the horizontal position:
    xPos++;
  }
  delay(16);
}

例程序 -- TFT 通用绘图显示

#include <TFT.h>  // Arduino LCD library
TFT TFTscreen = TFT();
// position of the line on screen
int xPos = 0;
void setup() {
  // initialize the serial port
  Serial.begin(9600);
  // initialize the display
  delay(1);
  TFTscreen.begin();
  delay(1);
  // clear the screen with a pretty color
  TFTscreen.background(250, 16, 200);
}
void loop() {
  // read the sensor and map it to the screen height
  int sensor = analogRead(A0);
  int drawHeight = map(sensor, 0, 1023, 0, TFTscreen.height());
  // print out the height to the serial monitor
  Serial.println(drawHeight);
  // draw a line in a nice color
  TFTscreen.stroke(250, 180, 10);
  TFTscreen.line(xPos, TFTscreen.height() - drawHeight, xPos, TFTscreen.height());
  // if the graph has reached the screen edge
  // erase the screen and start again
  if (xPos >= 160) {
    xPos = 0;
    TFTscreen.background(250, 16, 200);
  } else {
    // increment the horizontal position:
    xPos++;
  }
  delay(16);
}